FTDI · Component supply & purchasing
FT232HQ
Keep your programmer or interface board on its approved USB bridge. Request FT232HQ with the packing and operating mode your build needs.
- Package
- QFN-48
- Interface
- Single channel
- Packing
- Tray / reel
INTERFACE AT A GLANCE
Select the mode your released design uses. These are configuration choices, not simultaneous independent channels.
Keep the complete ordering requirement.
Resolve the package and carrier before comparing offers. The manufacturer references below establish device identity; the proposed lot and delivery terms are confirmed in your quotation.
| Order / record | What it means | Before you accept |
|---|---|---|
| FT232HQ | Single-channel FT232H in QFN-48 | Keep HQ in the BOM. FT232HL is a different package; FT232RN is a different device family. |
| FT232HQ-TRAY / FT232HQ-REEL | Manufacturer-listed packing options | State the required carrier and whether a traceable split quantity is acceptable. |
| External configuration record | Host-side settings and any external EEPROM image | Supply the approved version. Agree who may program or change sample configuration. |
Buy for the path your equipment actually uses.
A USB enumeration result can leave the production interface untested. Select your use below to see the information that makes a sample check meaningful.
Exercise the target transaction.
For a programming fixture, the useful result is a successful operation through the intended JTAG, SPI or I²C path. Name the approved host tool, target and clock setting; a serial-port loopback does not exercise that operation.
Protocol, target board, clock rate, host software version and a known-good transaction.
Define a transfer result.
An acquisition or test interface may depend on its FIFO mode. Agree synchronous or asynchronous operation, the host setup, payload and transfer duration. Keep USB link speed separate from the throughput required by your application.
FIFO mode, sustained payload target, test duration, acceptable errors and fixture.
Test the serial settings you ship.
For an industrial service interface, agree baud rate, framing and flow control together with the external transceiver or loopback arrangement. An RS-232 or RS-485 system includes circuitry beyond the USB bridge.
Baud rate, framing, flow control, host driver and signal-level arrangement.
The label record your receiving team needs.
Request a legible original outer label for the offered material. Compare it with the quotation and receiving record before a split reel or tray loses its connection to the original pack.
Use the illustrated FTDI guide to separate a package label, a laboratory shipment record and the chip’s top marking.
Explore FTDI labels and markingsFT232HQ · receiving record
- Device and carrier
- FT232HQ + TRAY or REEL
- Lot and count
- Original pack record
- Handling
- Seal, opening and repacking history
Retain the full offered form; a top mark alone does not settle original shipping format.
Ask which lot covers the useful first quantity and how a split carrier will be identified.
Ask the EMS what evidence and preparation it needs before QFN assembly.
Agree what the inspection must answer.
Identity, unused condition and a correct label matter. Application acceptance also depends on the interface, configuration and test conditions below.
Identity and physical condition
Compare marking and QFN outline with the original reference. Request terminal and exposed-pad views, dimensions and any observed surface damage or rework.
Configuration before traffic
Record the host tool and approved configuration. Read configuration first where feasible; obtain approval before writing an EEPROM or changing a sample.
The selected interface path
Use the MPSSE transaction, FIFO transfer or UART procedure agreed above. Specify fixture, limits and sample count; confirm laboratory feasibility before committing to a release date.
Agree the sampled lot, sample count, method, equipment, limits, report and disposition before work starts. Specialised functional testing is subject to laboratory feasibility and the agreed scope.
Can FT232RNL replace FT232HQ?
Treat it as an engineering change. The RN UART family does not provide the same H-device interface choices or QFN-48 footprint.
Do tray and reel need separate part approvals?
The carrier requirement should be explicit, while device approval remains tied to the complete manufacturer code and your released design. Agree any permitted repacking before ordering.
Look closely. Record the observation.
Visual inspection can document package condition and surface observations. Functional testing needs its own agreed procedure.
For this FT232HQ enquiry, request images and findings for the actual offered lot.
How to read a component inspection reportWhere a shortage can stop the build.
ICstoq reviews your requirement against our inventory and established China supply relationships. Keep the approved BOM line intact while we confirm a suitable lot, quantity and delivery window.
Coordinate an OEM / EMS shortage buyProgramming-fixture manufacturers
A missing USB bridge can stop a fixture build even when the target hardware is ready. Exact-part procurement preserves the released QFN footprint and programming setup.
Instrumentation and industrial-interface makers
Keep the data path and host software baseline attached to the BOM line so receiving can evaluate the part for the intended assembly.
Request FT232HQ for your build.
Send the quantity, required arrival date and destination. Include the conditions below so we can review supply and inspection together.
Send your FT232HQ enquiryUseful details for this device
- FT232HQ, required tray/reel format and quantity.
- MPSSE, FIFO or UART use, with the target or transfer requirement.
- Approved host environment and whether sample configuration may be changed.