FTDI · Component supply & purchasing
FT260Q-T
Keep the HID interface and tray requirement together. Request FT260Q-T for your approved sensor, controller or instrument assembly.
- Package
- WQFN-28
- USB class
- HID
- Suffix -T
- Tray
INTERFACE AT A GLANCE
HID communication on the host side. A virtual COM-port workflow is a different software requirement.
Keep the complete ordering requirement.
Resolve the package and carrier before comparing offers. The manufacturer references below establish device identity; the proposed lot and delivery terms are confirmed in your quotation.
| Order / record | What it means | Before you accept |
|---|---|---|
| FT260Q-T | 28-pin WQFN, tray packing | Here -T means tray. Do not apply a suffix convention from another manufacturer or family. |
| FT260Q-R | WQFN reel option | Accept a packing change only when your assembly team approves the carrier and handling. Keep the quotation specific. |
| FT260S | 28-pin TSSOP alternative package | This is not the same footprint as FT260Q. A matching UART/I²C description does not approve a substitution. |
Start with the HID command flow.
The host application must reach the peripheral in the way your product expects. Choose the function involved in your shortage purchase.
Use a known peripheral transaction.
For a sensor or controller interface, agree the peripheral address, bus speed, supply arrangement and a known read/write sequence. Include ACK behaviour and any error condition that matters to the application.
Peripheral type and address, bus speed, logic supply, command sequence and expected response.
Keep HID and UART checks connected.
The UART side still needs its serial settings, but host access is through the FT260 HID path. Opening a virtual COM port is not a substitute for exercising the approved application and its actual payload.
HID application or library version, UART framing, baud rate, flow control and payload.
Specify the complete use case.
If the assembly uses both interfaces, identify the required transactions and operating sequence for each. Agree the mode configuration and verify the intended combination on the nominated fixture.
Functions used together, mode configuration, host OS, fixture and expected results.
The label record your receiving team needs.
Request a legible original outer label for the offered material. Compare it with the quotation and receiving record before a split reel or tray loses its connection to the original pack.
Use the illustrated FTDI guide to separate a package label, a laboratory shipment record and the chip’s top marking.
Explore FTDI labels and markingsFT260Q-T · receiving record
- Full order
- FT260Q-T
- Packing relationship
- -T tray / -R reel
- Lot and handling
- Pack identification and exposure record
Keep the WQFN package and -T tray suffix together on the RFQ and purchase record.
Record the offered carrier separately from any supplier’s shortened FT260Q description.
Reconcile the delivered tray count and any repacked quantity with the receiving record.
Agree what the inspection must answer.
Identity, unused condition and a correct label matter. Application acceptance also depends on the interface, configuration and test conditions below.
WQFN condition
Request the package outline, marking, terminals and exposed-pad condition. Tie dimensions and observations to identified samples from the proposed lot.
HID communication
Use the specified host environment, application/library and configuration. Enumeration confirms only that limited step; it does not verify the attached peripheral path.
Peripheral operation
Agree the actual I²C read/write transaction or UART traffic, signal levels, timing and expected response. Record how failures and configuration discrepancies will be reviewed.
Agree the sampled lot, sample count, method, equipment, limits, report and disposition before work starts. Specialised functional testing is subject to laboratory feasibility and the agreed scope.
Does -T mean tape and reel?
No. FTDI’s FT260 ordering table uses -T for WQFN tray packing and -R for tape and reel.
Is a VCP loopback test enough?
It does not represent the FT260 host path. Agree HID access and the actual UART or I²C transaction your product needs.
Look closely. Record the observation.
Visual inspection can document package condition and surface observations. Functional testing needs its own agreed procedure.
For this FT260Q-T enquiry, request images and findings for the actual offered lot.
How to read a component inspection reportWhere a shortage can stop the build.
ICstoq reviews your requirement against our inventory and established China supply relationships. Keep the approved BOM line intact while we confirm a suitable lot, quantity and delivery window.
Coordinate an OEM / EMS shortage buySensor-interface and instrument manufacturers
An FT260 shortage can interrupt an otherwise released USB interface board. Keep the qualified HID software and peripheral protocol unchanged in the purchasing requirement.
Industrial controller and service-tool makers
Confirm tray feeding and incoming acceptance with the assembly team. A substitute USB-to-serial part can introduce a software change as well as a footprint change.
Request FT260Q-T for your build.
Send the quantity, required arrival date and destination. Include the conditions below so we can review supply and inspection together.
Send your FT260Q-T enquiryUseful details for this device
- FT260Q-T, tray quantity and delivery requirement.
- HID software, I²C peripheral/address or UART settings.
- Mode configuration, logic supply and required transaction for sample approval.