STM32H723ZGI6
Keep the 7 × 7 mm UFBGA144 requirement intact. An H723ZGT6 quotation changes the package; a general H7 match leaves memory, interfaces and assembly conditions unresolved.
144 connections. A specific BGA footprint.
- Flash
- 1 MB
- Body
- 7 × 7 mm
- Grade range
- −40 to +85°C
- Packing
- Tray
Manufacturer ordering reference · availability confirmed by quotation
Decode the code before you compare the offer.
Select a code segment to see its role. Keep the complete manufacturer order code on the quotation, BOM and receiving record.
| Order / record | What it means | Before you accept |
|---|---|---|
| ZGI6 / ZGT6 | UFBGA144 versus LQFP144. | Match the 7 × 7 mm body, ball map and land pattern; pin count alone does not establish a match. |
| G memory field | 1 MB Flash requirement. | Keep the image and boot arrangement within the approved memory configuration. |
| Tray delivery | Protect the ball array and orientation. | Confirm tray condition, lot separation and the actual pack’s moisture history before assembly. |
Set the buying conditions for your build.
Choose the situation closest to your requirement. These details help purchasing, engineering and the assembly team review the same offer.
Preserve the BGA manufacturing route.
A high-speed acquisition controller may already have its PCB and stencil released for the 0.5 mm BGA. A leaded H723 offer would change the board and process, even though both descriptions say 144 connections.
ZGI6, ball-map reference and EMS handling requirements.
Specify the populated memory interface.
If your application runs from or buffers data in external memory, include that device and configuration in sample acceptance. A programmer connection alone does not exercise the board’s memory timing or traffic.
Memory device, bus configuration, firmware image and workload.
Separate incoming condition from assembled joints.
Define what should be recorded about the incoming balls, substrate and marking. An X-ray or visual examination of loose parts does not establish solder-joint quality after your reflow process.
Sample count, ball-condition criteria and any separately agreed X-ray scope.
Read identity and handling as separate records.
The product label connects the full order code, lot and quantity. The moisture label records handling conditions. Use this actual STM32H757 example to locate the fields; obtain the offered STM32H723ZGI6 pack’s own limits before assembly.
Packaging-handling label
STMicroelectronics
STM32H757 handling-label example
Select a marker on the image or a number below. Each field answers a different purchasing question.

Sensitivity level
This caution label states moisture sensitivity. It does not contain the complete device order code; keep the product label or top mark with it.
Bag seal date
The seal date is a packaging event. If the bag has been opened or resealed, ask for that history separately.
Peak package temperature
This value concerns package assembly processing. It is not the permitted operating temperature of an STM32 device.
Exposure window and conditions
Read the time together with its stated conditions. A clock without temperature and humidity context is not a complete handling record.
Storage and baking references
The lower text describes storage and actions if conditions are exceeded. Baking must follow the applicable device, carrier and process requirements.
For the MCU you are buying, request its own label limits and opening history. The values in this example are not handling specifications for another STM32 device.
Discuss this requirement ↗For STM32H723ZGI6
ZGI6 UFBGA144, 7 × 7 mm footprint and 1 MB Flash requirement. Ball-condition criteria, tray acceptance and moisture history.
Turn the concern into an agreed inspection.
Original identity, unused condition and a correct order code are essential. Programming, handling and application behaviour need their own acceptance conditions.
BGA identity
Check ZGI6 and inspect the complete ball array, package edges and orientation reference.
Handling history
Review the offered pack’s seal, moisture label and opening record. Agree any corrective handling with the assembler.
Memory and interfaces
Test the released firmware’s memory and communication paths using a documented fixture and operating conditions.
Does ZGT6 have the same footprint?
No. It is a different package option. Request the exact ZGI6 code for the UFBGA144 board.
Does an incoming X-ray prove the finished board will pass?
No. Any incoming examination has a defined scope. Assembly-process and functional acceptance require their own criteria.
Before testing, agree the lot, sample count, method, fixture, limits, report and sample disposition. Electrical and specialised checks depend on laboratory feasibility; they are not implied by a visual inspection.
See how package observations are recorded.
This supplied AD5535BKBCZ report records orientation, solder balls and coplanarity. It illustrates the evidence format, not the condition of an STM32 lot. For your order, use the actual device drawing, agreed sample plan and appropriate package-specific criteria.
Keep the report connected to the sample, method and agreed limits. Review any exceptions before the lot is released.
Explore inspection report examplesWhere an exact-part shortage matters.
Keep your current EMS or assembly partner. A targeted purchase can address the missing BOM line while the approved design and receiving requirements stay under your control.
Coordinate an OEM / EMS shortage buyIndustrial acquisition boards
A compact BGA controller can be the missing line in a populated measurement BOM. Pin mapping and sustained data traffic matter at sample approval.
Embedded equipment controllers
Preserve external-memory and communication requirements when the delivery schedule makes a redesign impractical.
Bring the complete requirement.
ICstoq reviews our inventory and established China supply relationships against your quantity, required arrival date and destination. The quotation confirms the offered lot, packing, inspection and delivery terms.
Send your STM32H723ZGI6 enquiryUseful details for this enquiry
- ZGI6 UFBGA144, 7 × 7 mm footprint and 1 MB Flash requirement
- Ball-condition criteria, tray acceptance and moisture history
- External memory, active interfaces and the sample test workload
Tell us which conditions are fixed and which need discussion. Any alternative requires your approval before it replaces the requested part.